setting up yongnuo 622n for nikon supersync

SETTING UP YONGNUO 622N FOR NIKON SUPERSYNC HOW TO
SETTING UP YONGNUO 622N FOR NIKON SUPERSYNC MANUAL
SETTING UP YONGNUO 622N FOR NIKON SUPERSYNC SERIES

I think that I am missing something here.Ĭan someone who uses YN-622 with Nikon system please comment on this and if I am doing anything incorrectly. It does not appear that I am doing anything wrong, yet I find it hard to believe that the unit is defective.

SETTING UP YONGNUO 622N FOR NIKON SUPERSYNC MANUAL

I have read the manual and watched several you tube videos. If I set flash to M (manual) mode, the flash triggers as I take picture. I tried using the Test button and actually taking the picture. YN-622N i-TTL wireless transceiver is a high performance 2.4G wireless flash. switch(P.10), long press for Super Sync parameter setting (P.9). The communications between camera and flash works, as the flash wakes up with half button press, and zooms as I zoom my lens. 22, Up To 100M Range YN-622N Features: 1. YN-622N-TX i-TTL wireless flash controller is for supporting. SB-900 level is in 'ON' mode (not in remote or master mode). I've had quite a few comments and questions related to issues people have had with getting the Yongnuo YN622N-TX flash trigger to work with manual power cont. Buy Yongnuo YN-622N-TX YN622N-TX Transmitter LCD Wireless i-TTL Flash Controller 1/8000s Trigger Transmitter for Nikon DSLR at the lowest price in Hong Kong. It is in TTL mode (as indicated by green light). I am unable to trigger my SB-900 in TTL mode. Took 'Herb' the support guy at Quantum only a week and some testing to confirm: the D750s flash shoe is a little 'too long.I just recently purchased a YN-622n set for Nikon. Otherwise the pin doesn't seat, and the flash will not communicate with the body.

But on D750, like everyone else, I have to slide it in all the way, then pull back just a bit then lock it down. And a mysterious high end controller of some kind. The YN 560 TX which will be able to trigger the 560EX III flashes that have built in receivers. The YN 622N TX which functions as an enhanced master controller for YN 622N transceivers.

SETTING UP YONGNUO 622N FOR NIKON SUPERSYNC SERIES

The YN-622N utilizes a series of LEDs to display. On my D7100 I put it in the hotshoe, no issue, works great. Supposedly Yongnuo is releasing 3 trigger controllers this month. And, it can utilize 7 channels and 3 groups for setting up multiple flash units easily and efficiently. Compatible with Nikon i-TTL cameras, this controller slides directly into the hot shoe and utilizes a 2.4 GHz frequency with a range of 328' to trigger the remote flashes. I have this same problem with my Quantum flash. Control multiple flashes equipped with the YN-622N i-TTL transceiver with the YN-622N-TX i-TTL Wireless Flash Controller from Yongnuo. Its really just about making sure it clicks in but pushing it forward, lowering the pin a bit then pulling back until you hear it click.

SETTING UP YONGNUO 622N FOR NIKON SUPERSYNC HOW TO

I found this video on youtube of this guy showing exactly what the issue is and how to fix it. Are my units defective or is it normal to not lock them all the way in the hotshoe? New Yongnuo YN-560 IV Flash Speedlite for Canon Nikon Pentax Olympus DSLR Cameras. Now I can use my old Nikon SS-20 film flash, SB-70, SB-600 all at the same time with my. It must be said that the construction of the Yongnuo YN-622N is a bit better than that of the Pixel Kings, in particular the battery compartment. In order to do this setup I had to purchase 2 sets of radio triggers.

but lock them tiny bit on the outside part.ĭo you have similar problem with the trigger. While the YN-622C and Kings for Canon have a similar feature set, this is not the case for the respective Nikon i-TTL variants, which we will discover in a moment. I have ordered two different YN-622N-TX and I notice that the way to trigger successfully my yongnuo flash is to not push the TX units far inside on my hotshoe.

Setting up yongnuo 622n for nikon supersync